2007 Honda Odyssey

Canadian MSRP
$33,300 - $48,100
2007 Honda Odyssey

Key Specifications for 2007 Honda Odyssey

Fuel Economy 8.2 - 13.3 City/HWY combined
Horsepower 244 hp
Drivetrain Front-Wheel Drive
Engine Gasoline
Torque 240 ft-lb
Seats 7 - 8
 

Review & Compare:
2007 Honda Odyssey Trims

The 2007 Honda Odyssey has 5 trims. Below you will be able to review all the trims with the option to compare.
5 trims available
Select 1 more trim

Photos

No content available

AutoTrader Review

N/A

This vehicle has not yet been reviewed

Reviews and News

Recall Information

Recall number
Recall date
System affected
Model year(s) affected
Recall number
2014-076
Recall date
2014-03-14
System affected
Fuel Supply
Model year(s) affected
2005 2006 2007 2008 2009 2010
Manufacturer Recall Number:
HL99
Units Affected:
63,328
Notification Type:
Safety Mfr
On certain vehicles, the fuel pump strainer could deteriorate and crack. This could result in a fuel smell and/or fuel leak. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: Dealers will replace the fuel strainer cover.
Recall number
2013-381
Recall date
2013-11-04
System affected
Brakes
Model year(s) affected
2007 2008
Manufacturer Recall Number:
Units Affected:
24,692
Notification Type:
Safety TC
On certain vehicles, due to a defect in the Vehicle Stability Assist (VSA) system, the brakes may apply unexpectedly while the vehicle is being driven without the driver pressing on the brake pedal. If this were to occur, the brake lamps would also fail to illuminate. These issues could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will affect repairs.
Recall number
2010-364
Recall date
2010-10-22
System affected
Brakes
Model year(s) affected
2005 2006 2007
Manufacturer Recall Number:
HL06, AK34
Units Affected:
34,360
Notification Type:
Safety Mfr
On certain vehicles, a seal in the brake master cylinder may be susceptible to damage which can result in a leak if certain conditions exist. The polymer content affects the amount of lubrication the brake fluid provides to brake system components that are exposed to brake fluid. If the brake fluid is replaced with a low polymer brake fluid, and the brake fluid is subsequently subjected to a manual brake fluid bleeding procedure, as opposed to an automated brake bleed procedure, it is possible for the seal at the end of the brake master cylinder primary circuit to become twisted within its retention groove. If this seal becomes twisted, it can result in a leak of a small amount of brake fluid each time the brake pedal is applied. Should a leak occur, after some time the driver will be alerted by the illumination of the low brake fluid indicator light on the meter panel before any effect on braking performance results. If the driver continues to drive the vehicle without refilling the brake fluid reservoir, the vehicle will eventually exhibit a soft or spongy brake pedal feel, requiring more stroke to achieve equivalent braking force. Eventually, if this continues un-remedied, braking performance will be affected, and will finally result in a low pedal and a loss of one braking circuit. Correction: Dealers will replace the brake master cylinder seal cup and the master power assembly if brake fluid has leaked.
Recall number
2010-079
Recall date
2010-03-16
System affected
Brakes
Model year(s) affected
2007 2008
Manufacturer Recall Number:
HK96, HK95
Units Affected:
28,827
Notification Type:
Safety TC
On certain vehicles, during the self-check process that occurs shortly after each time the engine is started, the self-diagnostic software for the Vehicle Stability Assist (VSA) brake modulator causes a condition that can allow air to enter the modulator pump. Over time, and after starting the engine numerous times, it is possible for enough air to enter the system to change the brake pedal feel and affect braking performance. Reduced braking performance could lead to a crash causing property damage, personal injury or death. Correction: Dealers will remove existing air in the brake system then apply sealant and caps to the VSA modulator to prevent air from entering the brake system.

Similar Vehicles

Select Another Vehicle
Search now