Honda Odyssey

Issue: On certain vehicles equipped with a V6 engine, the connecting rod bearings could wear prematurely and become damaged. Safety Risk: An engine failure could cause a sudden loss of power and/or increase the risk of a vehicle fire. Both issues could increase the risk of a crash or injury. Corrective actions: Honda will notify owners by mail and advise you to take your vehicle to a dealership to inspect the engine. If damage is found, the dealer will replace the necessary parts.

Issue: On certain vehicles, the side mirror glass may not be attached properly. As a result, the mirror glass could vibrate or fall off. Safety Risk: A missing mirror will reduce rear visibility and could increase the risk of a crash. Corrective Actions: Honda will notify owners by mail. Due to a parts supply issue, Honda advises that you should only take your vehicle to a dealership if the mirror is loose, vibrating or has fully detached. Honda will send you a second notice when the replacement parts are available, and instruct you to take your vehicle to a dealership to replace the glass on both side mirrors.

Issue: On certain vehicles, the low-pressure fuel pump could fail. If this happens, then engine may run rough or may not start and the check engine light may turn on. This could also result in a sudden loss of engine power while driving. Note: This is an expansion of Transport Canada Recall No. 2020-236. Safety Risk: A sudden loss of engine power could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct you to take your vehicle to a dealer to replace the fuel pump motor.

Issue: On certain vehicles, a software problem could cause a delay or prevent the rearview camera image from displaying. Canadian regulations require the rearview image to display within 2 seconds of shifting the transmission into reverse gear. Safety Risk: A rearview camera image that is delayed or that does not display could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: Honda will notify owners by mail and include instructions on how to download and install a software update to correct this problem. Alternatively, an owner can take their vehicle to a dealer to have the software update installed.

Issue: On certain vehicles, moisture can freeze in the door handle cables for the rear sliding doors. If this happens, the door handle could stick in the open position. This can cause the door not latch properly when it is closed. As a result, the door could open while driving. Safety Risk: A door that opens while driving could create a risk of injury. Corrective Actions: Honda will notify owners by mail and instruct you to take your vehicle to a dealer to replace the cables for the outer handles on the power sliding doors.

Issue: On certain vehicles, exposure to moisture over time could cause the driver-front airbag not to inflate properly in a crash. In some cases, this could cause an airbag not to fully inflate, while in others it could cause it to deploy with more force than normal. It could also cause the inflator to rupture. If the airbag inflator ruptures, small pieces of metal could be propelled toward vehicle occupants or cause damage to the airbag and prevent its proper function. Note: This recall is for airbag inflators that may have been installed when the vehicle had the steering wheel airbag replaced. Safety Risk: In a crash requiring an airbag deployment, the driver-front airbag may not inflate properly or the inflator could rupture. This could create a risk of injury. Corrective Actions: The company will notify owners by mail. There may be a significant delay before replacement parts are available. The company will send you a second letter once replacement parts are available and instruct you to take your vehicle to a dealer to inspect the driver-front airbag inflator. If the inflator requires replacement, a newly design part will be installed.

Issue: On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Note: This is a new recall campaign that includes vehicles that had an airbag inflator replaced under a previous recall or had a replacement airbag installed. The previous recall provided an interim (short-term) repair. Interim repair parts must be replaced with the final repair parts provided in this recall. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Action: Owners will be notified by mail and instructed to take their vehicle to a dealer to replace the driver and/or passenger-front airbag inflator. Note: The Canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.

Issue: On certain vehicles, the teeth on the timing belt may separate due to a manufacturing issue. This could result in an engine stall. Safety Risk: An engine stall could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct them to take their vehicle to a dealer to inspect the lot number on the timing belt. If it is within the affected range, the belt will be replaced. Additionally, dealers will inspect the engine for internal damage.

On certain vehicles, the rear latch assemblies on the power sliding doors may stick. This could cause a door not to close fully, and in certain circumstances, the door may open unexpectedly while the vehicle is in motion. This could create a risk of injury to the occupants. Correction: Dealers will replace the rear latch assemblies on both sliding doors. In the interim, until vehicles can be completely repaired, dealers will disable the power opening and closing functions to prevent a door from opening unexpectedly.

On certain vehicles, the seat recliner mechanism for the second row left (driver’s) side seat may have a manufacturing error. If the second row left side seat walk-in feature (which folds the seatback and slides the seat forward for access to the third row) is operated while the seat is in the full recline position, the recliner cam could over rotate. When the seatback is returned to an upright position, there is a potential for the seatback to stay in unlocked position or unexpectedly unlock without engaging the lever. In the event of crash, an unlocked seatback could increase the risk of injury to the seat occupant. Correction: Dealers will test the seat to confirm proper operation. If the seat recliner is found to be operating properly, a stopper bracket (which limits the rotation of the cam) will be installed on the seat recliner mechanism. In cases where the seatback does not function properly, dealers will replace the seatback frame assembly and a stopper bracket will be installed and proper operation will be verified.

Certain vehicles may fail to comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 208 - Occupant Protection in Frontal Impacts. During vehicle assembly, an outer seat belt position seat belt tongue may have been incorrectly installed onto the third row seating centre seat belt assembly. This would result in the seat belt tongue not latching when inserted in the centre seat belt buckle, and therefore would be non-compliant with the standard. In the event of a crash, an unlatched seatbelt may increase the risk of injury to the seat occupant. Correction: Dealers will inspect the third row centre seat belt for the correct tongue and replace as necessary.

Certain vehicles may fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 207 - Anchorage of Seats. Due to a manufacturing error, the seat adjustment bar that controls the second row centre seat slide function may stick in the unlocked position, allowing the seat to slide freely and fail to meet the requirements of the standard. An unlocked second row centre seat may increase the risk of injury to the seat occupant in the event of a crash. Correction: Dealers will inspect the slide function for the second row centre seat and repair/replace the seat adjustment bar if necessary.

Certain vehicles may not comply with Canadian Motor Vehicle Safety Regulations. The compliance label may bear incorrect rear Gross Axle Weight Rating (GAWR) information (lower than the vehicle's actual rear GAWR). Correction: A production change has been undertaken to remedy this technical non-compliance condition. No corrective recall action is required as the technical non-compliance conditions are deemed to be non-safety related.

On certain vehicles, a defect in the supplemental restraint system (SRS) could result in an inadvertent deployment of the front airbag(s) and/or seatbelt pretensioner(s). Unintended seatbelt pretensioner and/or airbag deployment, in a non-warranted (non-impact) situation, could startle the driver, which could result in a vehicle crash causing property damage and/or personal injury. In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: Dealers will replace the SRS control unit and may install an in-line jumper wiring harness to correct the issue. Note: This recall supersedes recall 2013315. Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Dealers will inspect and, if necessary, replace the passenger airbag inflator. Note: This recall is an expansion of recall 2013111. Honda Canada has created a special Airbag Inflator Hotline for immediate assistance. For more information, please contact: For Honda Owners: 1-877-445-7754 For Acura Owners: 1-877-445-9844

On certain vehicles, the fuel pump strainer could deteriorate and crack. This could result in a fuel smell and/or fuel leak. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: Dealers will replace the fuel strainer cover.

On certain vehicles, a defect in the supplemental restraint system could result in an inadvertent deployment of the front airbags. Unintended airbag deployment, in a non-warranted (non-impact) situation, could startle the driver, which could result in a vehicle crash causing property damage and/or personal injury. In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: Dealers will install an electrical noise suppressor unit.

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the passenger airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Dealers will inspect and, if necessary, replace the passenger airbag inflator. Note: Honda Canada has created a special Airbag Inflator Hotline for immediate assistance. For more information, please contact: For Honda Owners: 1-877-445-7754 For Acura Owners: 1-877-445-9844

On certain vehicles, the ignition interlock blocking mechanism could become damaged if excessive force is applied to the ignition key. If this occurs, it may become possible for the driver to remove the ignition key when the gear selector is in a position other than the Park position. This could allow the vehicle to roll away, increasing the risk of a crash causing personal injury and/or damage to property. Correction: Dealers will install an updated ignition interlock lever and replace the ignition lock cylinder if necessary.

On certain vehicles, the driver's airbag inflator could produce excessive internal pressure. If an affected airbag deploys, the increased internal pressure may cause the inflator to rupture and metal fragments could pass through the airbag cushion material and cause injury to vehicle occupants. Correction: Dealers will replace airbag inflator.

On certain vehicles, a seal in the brake master cylinder may be susceptible to damage which can result in a leak if certain conditions exist. The polymer content affects the amount of lubrication the brake fluid provides to brake system components that are exposed to brake fluid. If the brake fluid is replaced with a low polymer brake fluid, and the brake fluid is subsequently subjected to a manual brake fluid bleeding procedure, as opposed to an automated brake bleed procedure, it is possible for the seal at the end of the brake master cylinder primary circuit to become twisted within its retention groove. If this seal becomes twisted, it can result in a leak of a small amount of brake fluid each time the brake pedal is applied. Should a leak occur, after some time the driver will be alerted by the illumination of the low brake fluid indicator light on the meter panel before any effect on braking performance results. If the driver continues to drive the vehicle without refilling the brake fluid reservoir, the vehicle will eventually exhibit a soft or spongy brake pedal feel, requiring more stroke to achieve equivalent braking force. Eventually, if this continues un-remedied, braking performance will be affected, and will finally result in a low pedal and a loss of one braking circuit. Correction: Dealers will replace the brake master cylinder seal cup and the master power assembly if brake fluid has leaked.

On certain vehicles, the driver's airbag inflator could produce excessive internal pressure. If an affected airbag deploys, the increased internal pressure may cause the inflator to rupture and metal fragments could pass through the airbag cushion material and cause injury to vehicle occupants. Correction: Dealers will replace airbag inflator. Note: Honda Canada has created a special Airbag Inflator Hotline for immediate assistance. For more information, please contact: For Honda Owners: 1-877-445-7754 For Acura Owners: 1-877-445-9844 Update June 2016: New U.S. research shows that these Takata airbags may be at higher risk of failure. Please ensure you have this recall done if your vehicle is affected.

Certain vehicles located in Alberta, Saskatchewan, Manitoba and the Yukon may experience a combination of extreme low temperatures and very rough road conditions, causing a crack in the fuel sending unit flange. At this time, vehicles located in other parts of the country are not experiencing this type of failure, therefore no action will be undertaken by the manufacturer in unaffected provinces and territories. A cracked flange could allow fuel to leak which, in the presence of an ignition source, could result in a fire. Correction: Dealers will replace the fuel sending unit.

On certain vehicles, a rear wheel speed sensor may not have been installed correctly, which causes the sensor to report an incorrect wheel speed to the anti-lock brake system (ABS) control unit. The on-board diagnostic system quickly identifies this error under most normal driving conditions and activates numerous warning lamps and disables the ABS. Brake application below the ABS threshold, or after ABS is disabled, is not affected. However, if brake application exceeding the ABS threshold occurs before the malfunction is detected, the ABS control unit may reduce brake force to all wheels. An unexpected loss of brake force can cause a crash. Correction: Dealers will inspect the rear wheel speed sensors. If an incorrect gap is detected, the sensor will be removed and the knuckle checked for cross-threading damage and replaced, if necessary.

Certain operating conditions can result in heat build-up between the countershaft and secondary shaft second gears in the automatic transmission, eventually leading to gear tooth chipping or, in very rare cases, gear breakage can occur. Gear failure could result in transmission lock-up. Correction: On vehicles with 24 000 kms or less, the dealer will update the transmission with a simple revision to the oil cooler return line to increase lubrication to second gear. On vehicles with more than 24 000 kms, the dealer will inspect the transmission to identify gears that have already experienced discoloration due to overheating. If discolouration exists, the transmission will be replaced. If discolouration is not present, the dealer will perform the revision to the oil cooler return line.

On certain vehicles, a dash light dimmer circuit, mounted in the multiplex control unit may be damaged by heat build-up if the dimmer circuit is operated at a setting that is less than full intensity. This would cause a transistor in the module to fail resulting in loss of instrument cluster lighting. Such a condition would prevent the driver from reading the speedometer or other instruments when operating the vehicle in the dark. Correction: Multiplex unit will be replaced.